D7net
Home
Console
Upload
information
Create File
Create Folder
About
Tools
:
/
proc
/
self
/
root
/
proc
/
thread-self
/
root
/
lib
/
dracut
/
modules.d
/
95fcoe
/
Filename :
module-setup.sh
back
Copy
#!/bin/bash # called by dracut check() { is_fcoe() { block_is_fcoe $1 || return 1 } [[ $hostonly ]] || [[ $mount_needs ]] && { for_each_host_dev_and_slaves is_fcoe || return 255 } require_binaries dcbtool fipvlan lldpad ip readlink fcoemon fcoeadm || return 1 return 0 } # called by dracut depends() { echo network rootfs-block return 0 } # called by dracut installkernel() { instmods fcoe libfcoe 8021q edd bnx2fc } get_vlan_parent() { local link=$1 [ -d $link ] || return read iflink < $link/iflink for if in /sys/class/net/* ; do read idx < $if/ifindex if [ $idx -eq $iflink ] ; then echo ${if##*/} fi done } # called by dracut cmdline() { { for c in /sys/bus/fcoe/devices/ctlr_* ; do [ -L $c ] || continue read enabled < $c/enabled read mode < $c/mode [ $enabled -eq 0 ] && continue if [ $mode = "VN2VN" ] ; then mode="vn2vn" else mode="fabric" fi d=$(cd -P $c; echo $PWD) i=${d%/*} ifname=${i##*/} read mac < ${i}/address s=$(dcbtool gc ${i##*/} dcb 2>/dev/null | sed -n 's/^DCB State:\t*\(.*\)/\1/p') if [ -z "$s" ] ; then p=$(get_vlan_parent ${i}) if [ "$p" ] ; then s=$(dcbtool gc ${p} dcb 2>/dev/null | sed -n 's/^DCB State:\t*\(.*\)/\1/p') ifname=${p##*/} fi fi if [ "$s" = "on" ] ; then dcb="dcb" else dcb="nodcb" fi # Some Combined Network Adapters(CNAs) implement DCB in firmware. # Do not run software-based DCB or LLDP on CNAs that implement DCB. # If the network interface provides hardware DCB/DCBX capabilities, # DCB_REQUIRED in "/etc/fcoe/cfg-xxx" is expected to set to "no". # # Force "nodcb" if there's any DCB_REQUIRED="no"(child or vlan parent). grep -q "^[[:blank:]]*DCB_REQUIRED=\"no\"" /etc/fcoe/cfg-${i##*/} &>/dev/null [ $? -eq 0 ] && dcb="nodcb" if [ "$p" ] ; then grep -q "^[[:blank:]]*DCB_REQUIRED=\"no\"" /etc/fcoe/cfg-${p} &>/dev/null [ $? -eq 0 ] && dcb="nodcb" fi echo "ifname=${ifname}:${mac}" echo "fcoe=${ifname}:${dcb}:${mode}" done } | sort | uniq } # called by dracut install() { inst_multiple ip dcbtool fipvlan lldpad readlink lldptool fcoemon fcoeadm if [ -e "/etc/hba.conf" ]; then inst_libdir_file 'libhbalinux.so*' inst_simple "/etc/hba.conf" fi mkdir -m 0755 -p "$initdir/var/lib/lldpad" mkdir -m 0755 -p "$initdir/etc/fcoe" if [[ $hostonly_cmdline == "yes" ]] ; then local _fcoeconf=$(cmdline) [[ $_fcoeconf ]] && printf "%s\n" "$_fcoeconf" >> "${initdir}/etc/cmdline.d/95fcoe.conf" fi inst_multiple /etc/fcoe/cfg-* inst "$moddir/fcoe-up.sh" "/sbin/fcoe-up" inst "$moddir/fcoe-edd.sh" "/sbin/fcoe-edd" inst "$moddir/fcoe-genrules.sh" "/sbin/fcoe-genrules.sh" inst_hook pre-trigger 03 "$moddir/lldpad.sh" inst_hook cmdline 99 "$moddir/parse-fcoe.sh" inst_hook cleanup 90 "$moddir/cleanup-fcoe.sh" inst_hook shutdown 40 "$moddir/stop-fcoe.sh" dracut_need_initqueue }