D7net
Home
Console
Upload
information
Create File
Create Folder
About
Tools
:
/
proc
/
self
/
root
/
proc
/
self
/
root
/
usr
/
include
/
linux
/
can
/
Filename :
netlink.h
back
Copy
/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ /* * linux/can/netlink.h * * Definitions for the CAN netlink interface * * Copyright (c) 2009 Wolfgang Grandegger <wg@grandegger.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the version 2 of the GNU General Public License * as published by the Free Software Foundation * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ #ifndef _CAN_NETLINK_H #define _CAN_NETLINK_H #include <linux/types.h> /* * CAN bit-timing parameters * * For further information, please read chapter "8 BIT TIMING * REQUIREMENTS" of the "Bosch CAN Specification version 2.0" * at http://www.semiconductors.bosch.de/pdf/can2spec.pdf. */ struct can_bittiming { __u32 bitrate; /* Bit-rate in bits/second */ __u32 sample_point; /* Sample point in one-tenth of a percent */ __u32 tq; /* Time quanta (TQ) in nanoseconds */ __u32 prop_seg; /* Propagation segment in TQs */ __u32 phase_seg1; /* Phase buffer segment 1 in TQs */ __u32 phase_seg2; /* Phase buffer segment 2 in TQs */ __u32 sjw; /* Synchronisation jump width in TQs */ __u32 brp; /* Bit-rate prescaler */ }; /* * CAN harware-dependent bit-timing constant * * Used for calculating and checking bit-timing parameters */ struct can_bittiming_const { char name[16]; /* Name of the CAN controller hardware */ __u32 tseg1_min; /* Time segement 1 = prop_seg + phase_seg1 */ __u32 tseg1_max; __u32 tseg2_min; /* Time segement 2 = phase_seg2 */ __u32 tseg2_max; __u32 sjw_max; /* Synchronisation jump width */ __u32 brp_min; /* Bit-rate prescaler */ __u32 brp_max; __u32 brp_inc; }; /* * CAN clock parameters */ struct can_clock { __u32 freq; /* CAN system clock frequency in Hz */ }; /* * CAN operational and error states */ enum can_state { CAN_STATE_ERROR_ACTIVE = 0, /* RX/TX error count < 96 */ CAN_STATE_ERROR_WARNING, /* RX/TX error count < 128 */ CAN_STATE_ERROR_PASSIVE, /* RX/TX error count < 256 */ CAN_STATE_BUS_OFF, /* RX/TX error count >= 256 */ CAN_STATE_STOPPED, /* Device is stopped */ CAN_STATE_SLEEPING, /* Device is sleeping */ CAN_STATE_MAX }; /* * CAN bus error counters */ struct can_berr_counter { __u16 txerr; __u16 rxerr; }; /* * CAN controller mode */ struct can_ctrlmode { __u32 mask; __u32 flags; }; #define CAN_CTRLMODE_LOOPBACK 0x01 /* Loopback mode */ #define CAN_CTRLMODE_LISTENONLY 0x02 /* Listen-only mode */ #define CAN_CTRLMODE_3_SAMPLES 0x04 /* Triple sampling mode */ #define CAN_CTRLMODE_ONE_SHOT 0x08 /* One-Shot mode */ #define CAN_CTRLMODE_BERR_REPORTING 0x10 /* Bus-error reporting */ #define CAN_CTRLMODE_FD 0x20 /* CAN FD mode */ #define CAN_CTRLMODE_PRESUME_ACK 0x40 /* Ignore missing CAN ACKs */ #define CAN_CTRLMODE_FD_NON_ISO 0x80 /* CAN FD in non-ISO mode */ /* * CAN device statistics */ struct can_device_stats { __u32 bus_error; /* Bus errors */ __u32 error_warning; /* Changes to error warning state */ __u32 error_passive; /* Changes to error passive state */ __u32 bus_off; /* Changes to bus off state */ __u32 arbitration_lost; /* Arbitration lost errors */ __u32 restarts; /* CAN controller re-starts */ }; /* * CAN netlink interface */ enum { IFLA_CAN_UNSPEC, IFLA_CAN_BITTIMING, IFLA_CAN_BITTIMING_CONST, IFLA_CAN_CLOCK, IFLA_CAN_STATE, IFLA_CAN_CTRLMODE, IFLA_CAN_RESTART_MS, IFLA_CAN_RESTART, IFLA_CAN_BERR_COUNTER, IFLA_CAN_DATA_BITTIMING, IFLA_CAN_DATA_BITTIMING_CONST, IFLA_CAN_TERMINATION, IFLA_CAN_TERMINATION_CONST, IFLA_CAN_BITRATE_CONST, IFLA_CAN_DATA_BITRATE_CONST, IFLA_CAN_BITRATE_MAX, __IFLA_CAN_MAX }; #define IFLA_CAN_MAX (__IFLA_CAN_MAX - 1) /* u16 termination range: 1..65535 Ohms */ #define CAN_TERMINATION_DISABLED 0 #endif /* !_UAPI_CAN_NETLINK_H */